Plumbing Basics: The First Step for When Installing a Bathtub
Plumbing Basics: The First Step for When Installing a Bathtub
Blog Article
They are making several good points relating to How to Install a Bathtub Yourself overall in this content directly below.
Setting up a tub isn't precisely rocket science, but it does require strong plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a reasonably challenging job. If the old tub is readily easily accessible, the project can move speedily; if you need to open up a wall to get rid of the old tub and place the new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old bathtub and also set in the new one. See to it you have qualified yourself for the task and also fit trying it. Rather than hiring a service provider to take control of a halfway-completed task, it is far better to consider employing one before you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you mount a brand-new tub in your restroom if you have currently gotten a new bathtub as well as don't require to alter the setup of your previous supply of water pipes.
Your devices as well as product list ought to make up the following:
Getting ready for the Installation
First of all, the supporting structure provided with the bath must be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its final position.
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you ought to do is disconnect the water supply. After doing so, switch on the taps to drain any water continuing to be in the system. The process of removing the existing taps can be fairly troublesome due to the limited access that is often the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the taps. Have a cloth prepared for the continuing to be water that will originate from the pipelines. Once the supply pipes have been gotten rid of, use the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single taps from turning during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned of any type of old sealing compound.
Prior to moving on to fit the new faucets, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Mounting the Bath tub
Making use of the two wooden boards under its feet, position the tub in the required setting. The wood boards are practical in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 little factors.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bath tub until the spirit level checks out degree.
To mount faucets, fit all-time low of the furthest flexible tap port to the appropriate supply pipe by making a compression sign up with; after that do the very same for the other tap.
Turn on the water and also examine all joints as well as new pipework for leaks and tighten them if necessary. Load the tub and also examine the overflow electrical outlet and the normal electrical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the maker's instruction manual. Tiling and also sealing around the bath tub should wait till the bathtub has actually been utilized at least when as this will certainly settle it into its final position.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the tap and also the various other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines remain in location between the faucet and also the sink. Protect the tap in position with the supplier given backnut. When the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The former kind ought to be attached to the tap finishes initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bath fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to split a stiff seal, triggering the water to permeate the wall surface in between the bathroom and the tiling, resulting in issues with wetness as well as feasible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your components and fittings. They are sold in tubes and cartridges, and also are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of drenched paper or soft rope. Remember to constantly load the tub with water prior to sealing, to enable the movement experienced when the bathtub remains in use. The sealant can fracture fairly very early if you do not consider this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise easily available on the marketplace. It is recommended to fit the ceramic tiles making use of waterproof or waterproof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent person who reads on Installing A Bathtub, I was thinking sharing that piece of content was essential. Don't hesitate to take the time to promote this blog post if you appreciated it. Thank you for your time. Please pay a visit to our website back soon.
Quality solution? Call. Report this page